Home › Constituents › M4

M4 — Shallow Water First Overtide of M2

The M4 constituent represents the shallow water first overtide of m2 component in harmonic tidal prediction. In classical analog tide-predicting machines, this partial wave was generated by an oscillating crank and Scotch yoke driven by a designated gear train.

⚡ Key Harmonic Constants for M4

Tidal Species: Shallow-Water Overtide
Angular Speed: 57.968208°/hr
Astronomical Period: 6.2103 hours
Doodson Number: 455.555
Equilibrium Force: 16% of M2
Origin: Hydrodynamic overtide

1. Astronomical & Hydrodynamic Origin

Not an astronomical force, but the hydrodynamic distortion of the M2 wave caused by seabed friction and non-linear continuity in shallow water.

Causes asymmetric tides where the flood duration differs drastically from the ebb, sometimes producing a tidal bore.

2. Mechanical Role in Historical Tide Predictors

Rotates at exactly twice the speed of M2 (2 * 28.9841042° = 57.9682084°/hr). Enabled mechanical predictors to forecast "double high waters" and distorted estuarine curves.

Gear Ratio Implementation:
Exact 2:1 gear ratio driven off the M2 primary shaft, eliminating the need for an independent astronomical gear train.

On historic calculators such as US Coast Survey Machine No. 2 ("Brass Brains") and the Bidston Observatory Doodson-Légé machines, each shaft had to maintain exact angular synchronisation with solar clockwork over 8,760 hours of continuous calculation without drifting out of phase.

3. Practical Operator Setup: 3-Step Configuration Guide

How did an analog computer technician dial the M4 constituent into a brass tide-predicting machine before a 365-day charting run? Follow the standard hydrographic office protocol:

  1. Step 1: Set Crank Throw (Amplitude H)
    Extract M4 amplitude and local phase lag derived from shallow-water estuary surveys.
  2. Step 2: Align Initial Epoch Angle (Phase Lag κ)
    Set the M4 crank arm; note that M4 requires high precision since small amplitude errors dramatically alter curve asymmetry.
  3. Step 3: Pulley Wire Tension Verification
    Engage the 2:1 speed-up gear linkage with the M2 drive shaft.

4. Physical Error & Mechanical Troubleshooting

Analog computers were governed by the laws of friction, backlash, and mechanical tolerances. Operating the M4 constituent presented distinct physical challenges:

Known Error Source Observed Mechanical Symptom Historical Corrective Action
High-speed shaft vibration on rapid 6-hour rotation Acoustic chattering of the M4 crank pin at higher operator cranking speeds. Limit manual crank rotational speed to under 40 RPM when tracing estuarine charts, or damp the Scotch yoke with felt pads.

For a complete review of analog calculation tolerances, see our study on Friction, Backlash, and Wire Stretch: Where Error Lived in Brass Computers.

5. Harbor Case Studies: Typical Amplitudes for M4

Because each body of water resonates with different astronomical frequencies, the amplitude of M4 varies dramatically around the globe:

Reference Harbor Typical Amplitude Local Tidal Characteristics
Southampton, UK 0.34 m Famous "double high water" allowing ships extended docking time without grounding.
Havre, France 0.40 m Creates a prolonged high-water stand ("tenue du plein") vital for port operations.
Anchorage, Alaska, USA 0.48 m Intense shallow water distortion driving rapid 10-meter tidal bores in Turnagain Arm.

Simulate M4 in Real-Time

Observe how M4 interferes with other harmonic waves on our virtual brass analog synthesizer. Adjust frequency, amplitude, and phase angle interactively.

Launch Harmonic Synthesizer ›

Frequently Asked Questions

Why is M4 called an "overtide"?

Just like overtones in music, when a pure tidal sine wave travels through shallow water where depth is comparable to wave amplitude, it distorts non-linearly, generating harmonics at twice (M4), three times (M6), and four times (M8) the base frequency.

How does M4 cause the famous "double high water" in Southampton?

When M4 peaks out of phase with M2, it creates a dip right in the middle of the M2 high-water crest. This transforms a single rounded peak into two distinct high waters separated by a minor drop.

Did Kelvin’s 1872 predictor include M4?

No. Early predictors lacked overtides, which made them incapable of predicting estuarine harbors like London or Southampton until Doodson and Harris added them.

Related Harmonic Constituents

Diurnal 15.04°/h

K1 — Luni-Solar Diurnal

The declination of both the Moon and Sun north and south of Earth’s equator during their orbital cyc...