Home › Constituents › M6

M6 — Shallow Water Sixth-Diurnal Overtide

The M6 constituent represents the shallow water sixth-diurnal overtide component in harmonic tidal prediction. In classical analog tide-predicting machines, this partial wave was generated by an oscillating crank and Scotch yoke driven by a designated gear train.

⚡ Key Harmonic Constants for M6

Tidal Species: Shallow-Water Overtide
Angular Speed: 86.952313°/hr
Astronomical Period: 4.1402 hours
Doodson Number: 655.555
Equilibrium Force: 5.2% of M2
Origin: Hydrodynamic overtide

1. Astronomical & Hydrodynamic Origin

Third harmonic of M2 generated by extreme frictional resistance along the seabed in shallow estuaries and rivers.

Produces steep, rapid tidal rise followed by an extended, slow fall, contributing to saw-tooth tidal curves.

2. Mechanical Role in Historical Tide Predictors

Runs at three times the speed of M2 (3 * 28.9841042° = 86.9523127°/hr). One of the fastest-spinning shafts on any mechanical predictor.

Gear Ratio Implementation:
Exact 3:1 speed multiplier train connected directly to the M2 drive shaft.

On historic calculators such as US Coast Survey Machine No. 2 ("Brass Brains") and the Bidston Observatory Doodson-Légé machines, each shaft had to maintain exact angular synchronisation with solar clockwork over 8,760 hours of continuous calculation without drifting out of phase.

3. Practical Operator Setup: 3-Step Configuration Guide

How did an analog computer technician dial the M6 constituent into a brass tide-predicting machine before a 365-day charting run? Follow the standard hydrographic office protocol:

  1. Step 1: Set Crank Throw (Amplitude H)
    Confirm M6 constituent constants from high-frequency gauge sampling.
  2. Step 2: Align Initial Epoch Angle (Phase Lag κ)
    Dial the fine M6 amplitude setting onto the high-order harmonic bank.
  3. Step 3: Pulley Wire Tension Verification
    Check that the M6 Scotch yoke slider is balanced to prevent harmonic vibration.

4. Physical Error & Mechanical Troubleshooting

Analog computers were governed by the laws of friction, backlash, and mechanical tolerances. Operating the M6 constituent presented distinct physical challenges:

Known Error Source Observed Mechanical Symptom Historical Corrective Action
Harmonic resonance in machine frame from high-speed rotation Audible hum and trembling of the tracing pen on chart paper. Bolt machine cast-iron base directly to masonry piers and operate drive crank at a steady, measured cadence.

For a complete review of analog calculation tolerances, see our study on Friction, Backlash, and Wire Stretch: Where Error Lived in Brass Computers.

5. Harbor Case Studies: Typical Amplitudes for M6

Because each body of water resonates with different astronomical frequencies, the amplitude of M6 varies dramatically around the globe:

Reference Harbor Typical Amplitude Local Tidal Characteristics
Severn Estuary, UK 0.15 m Drives the steep front of the Severn Bore during extreme spring tides.
Hooghly River / Kolkata, India 0.18 m Extreme river distortion creating dangerous tidal bores.
Seine Estuary, France 0.12 m Generates the historical "mascaret" tidal surge phenomenon.

Simulate M6 in Real-Time

Observe how M6 interferes with other harmonic waves on our virtual brass analog synthesizer. Adjust frequency, amplitude, and phase angle interactively.

Launch Harmonic Synthesizer ›

Frequently Asked Questions

Why is M6 three times faster than M2?

In non-linear shallow-water wave theory, the cubic term of bottom friction generates third harmonics. Because M2 has a ~12.42h period, M6 has a period of roughly 4.14 hours.

Which tide predicting machines featured M6?

US Machine No. 2, the Bidston Doodson-Légé machines, and German Gezeitenrechenmaschine III all included M6 to handle European and American estuarine harbors.

How did operators prevent M6 gears from wearing out?

Because M6 completed over 2,100 revolutions per prediction year, its brass gears were cut from hardened phosphor-bronze with specialized tooth profiles.

Related Harmonic Constituents

Diurnal 15.04°/h

K1 — Luni-Solar Diurnal

The declination of both the Moon and Sun north and south of Earth’s equator during their orbital cyc...